AudioCodes MediaPack 114 Instrukcja Użytkownika Strona 373
- Strona / 390
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Version 5.6 373 November 2008
SIP User's Manual 8. Networking Capabilities
8.8.3 Getting Started with VLANS and Multiple IPs
By default, the device operates without VLANs and multiple IPs, using a single IP address,
subnet mask and default Gateway IP address. This section provides an example of the
configuration required to integrate the device into a multiple IPs network withVLANs, using
the Web interface (refer to ''Integrating Using the Web Interface'' on page 373) and ini file
(refe
r to ''Integrating Using the ini File'' on page 375). The followi
ng table shows an example
configuration used in this subsection:
Table 8-2: Example of VLAN and Multiple IPs Configuration
Network
Type
IP Address
Subnet
Mask
Default Gateway
IP Address
VLAN ID
External Routing
Rule
OAMP 10.31.174.50 255.255.0.0 0.0.0.0 4 83.4.87.X
Control 10.32.174.50 255.255.0.0 0.0.0.0 5 130.33.4.6
Media 10.33.174.50 255.255.0.0 10.33.0.1 6 --
Notes:
• The values provided in this section are only used as an example.
• Since a default Gateway is available only for the Media network, for the
device to be able to communicate with an external device/network on its
OAMP and Control networks, IP routing rules must be used.
8.8.3.1 Integrating Using the Web Interface
The procedure below describes how to integrate the device into a multiple IPs network
withVLANs, using the Web interface.
¾ To integrate the device into a multiple IPs network withVLANs
using the Web interface, take these 6 steps:
1. Access the Web interface (refer to ''Accessing the Web Interface'' on page 21).
2. Use the Software Upgrade Wizard (refer to ''Software Upgrade Wizard'' on page 212)
to load and bu
rn the firmware version to the device (VLANs and multiple IPs support is
available only when the firmware is burned to flash).
3. Configure the VLAN parameters by completing the following steps:
a. Open the 'IP Settings' page (refer to ''Configuring the IP Settings'' on page 52).
b. Modify the VLAN parameters to correspond to the values shown in the following
figure:
Figure 8-3: VLAN Configuration in the IP Settings Page
- User's Manual 1
- Table of Contents 3
- List of Figures 8
- List of Tables 11
- WEEE EU Directive 13
- Customer Support 13
- Trademarks 13
- Related Documentation 14
- 1 Overview 15
- 1.2 MediaPack Features 16
- 1.3 SIP Overview 17
- Reader’s Notes 18
- 2 Configuration Concepts 19
- 3 Web-Based Management 21
- 3.3.1 Toolbar 24
- 3.3.2 Navigation Tree 25
- 3.3.3.1 Accessing Pages 28
- 3.3.3.2 Viewing Parameters 28
- 3.3.3.5 Working with Tables 32
- 3.3.5.1 Creating a Scenario 36
- 3.3.5.3 Editing a Scenario 39
- 3.3.5.6 Deleting a Scenario 42
- 3.3.7 Getting Help 47
- 3.3.8 Using the Home Page 48
- (grey): channel inactive 49
- 3.4 Configuration Tab 52
- [0] = OAMP (default) 65
- [1] = Media 65
- [2] = Control 65
- 3.4.2 Media Settings 67
- [2] Bypass 70
- [3] Events Only 70
- 3.4.3 Security Settings 79
- [1] Enable = Enabled 116
- [0] Disable (default) 116
- [1] Enable 116
- 5 steps: 120
- To the default Proxy 121
- 3.4.4.1.4 Coders 123
- 4 steps: 130
- 3.4.4.2.3 Metering Tones 144
- 3.4.4.2.5 Keypad Features 147
- 3.4.4.6.1 Authentication 175
- 3.4.4.6.2 Automatic Dialing 176
- 3.4.4.6.4 Call Forward 178
- 3.4.4.6.6 Call Waiting 180
- Disable (default) 188
- No = Don't register 189
- Yes = Register 189
- 3.4.5 Advanced Applications 190
- [1] Enable (Bellcore) 194
- [2] Ericsson MD-110 194
- [3] NEC (ICS) 194
- 3.5 Management Tab 198
- 3.5.1.3 Maintenance Actions 207
- 2 steps: 209
- 3.5.2 Software Update 210
- 3.6.2 Gateway Statistics 223
- 3.6.2.1 Call Counters 224
- 3.6.2.2 Call Routing Status 226
- 3.6.2.3 Registration Status 227
- 3.6.2.5 IP Connectivity 228
- 4 ini File Configuration 231
- 4.2 The ini File Structure 232
- 4.3 Modifying an ini File 235
- 4.4.1 Networking Parameters 236
- 4.4.2 System Parameters 244
- [0] = Disabled (default) 251
- 4.4.4 Security Parameters 252
- 4.4.5 RADIUS Parameters 257
- 4.4.6 SNMP Parameters 258
- [1] = Enabled 268
- Port = Port number 268
- UserId = User name 272
- UserPassword = Password 272
- 4.4.8 Voice Mail Parameters 277
- 4.4.9 PSTN Parameters 279
- [66] = TBR21 280
- Npi = Number Plan 297
- Ton = Type of Number 297
- 4.4.12 Channel Parameters 298
- [0] = Disable (default) 299
- [1] = Enable 299
- [1] Enable (default) 304
- 5 Default Settings 305
- 6.4 Coefficient File 312
- 6.5 User Information File 313
- 7 IP Telephony Capabilities 315
- 7.1.1 Configuring SAS 316
- 7.3.2.1 T.38 Fax Relay Mode 319
- 7.3.3 Supporting V.34 Faxes 324
- 7.4 FXO Operating Modes 326
- 7.4.1.1 One-Stage Dialing 327
- 7.4.1.2 Two-Stage Dialing 328
- 7.4.1.4 DID Wink 329
- 7.4.2 Telephone-to-IP Calls 330
- Connectivity and QoS) 335
- 7.11 Call Detail Record 339
- 7.13 Configuration Examples 342
- 7.14.3 Call Transfer 359
- 7.14.4 Call Forward 360
- 7.14.5 Call Waiting 361
- 7.14.7 Caller ID 362
- 8 Networking Capabilities 365
- 8.2.1 STUN 366
- 8.2.3 No-Op Packets 367
- 8.3 IP Multicasting 368
- 8.8 VLANS and Multiple IPs 370
- Control: Premium control 372
- Management: Bronze 372
- 10.1 MP-11x Specifications 381
- 10.2 MP-124 Specifications 384
- 11 Glossary 387
Powiązane produkty i podręczniki dla Bramy / kontrolery AudioCodes MediaPack 114
(44 strony)
(44 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji